![]() ![]() The web GUI launches automatically when you open a web browser. Connect another network cable from your computer to the yellow Ethernet port on your router.Ģ. Connect the network cable from your modem to the blue Ethernet port on your router. LTE antennas before powering on your router. Insert your micro SIM card and install the You can set up your LTE router via wired or wireless connection. Check your cable/DSL modem LED lights to ensure Connect your modem to the router with the bundled network cable.ģ. NOTE: If you are using DSL for Internet, you will need your username/password from your Internet Service Provider (ISP) to properly configure the router.Ģ. If it has a battery backup, remove the battery. 3G/4G signal LED (from strong to weak signal) 11. NOTE: If any of the items is damaged or missing, contact your retailer.ġ. Pycc Român Español Srpski Slovencina Slovenscina Svenska TürkçeĤG-AC68U Wireless Router Network cable (RJ-45) 2 * 3G/4G antennas 165Įnglish Hrvatski Cestina Dansk Nederlands Eesti Français Suomiĭeutsch Magyar Italiano Lietuvi Latviesu Norsk Português Polski Remembering your wireless router settings. I rather believe we are too far from the carrier antennas (2.5 km) to be able to receive any signal in this 5G NR NSA mode.Īlthough RSRP, RSRQ and SINR are average or bad, as the download and upload performances with 4G are rather good (30 to 100 Mbit/s down, and 10 to 30 Mbit/s up), we will probably keep the router and send back the antenna.File Info : application/pdf, 176 Pages, 18.93MB Document Document U12144 4G AC68U QSG 4G-AC68U ![]() Zyxel support suspects my Halo & Son antenna is not compatible with the 3500 MHz range (I checked: the manufacturer claims the antenna covers the 3400-3800 MHz range). When the switch is on EXT position without any external antenna connected, the router works only on 4G/3G/UMTS modes (5G signal could still be received but at a very low level by the external antenna circuit they made tests: 5G signal with the switch on INT RSRP = -65 dBm, 5G signal with the switch on EXT no external antenna connected RSRP = -90 dBm). ![]() 2600 MHz and below) when external antennas are connected and with the switch on EXT position when the switch is on INT position, internal antennas are used for all the ranges of frequency. The external antenna ports are only for frequencies higher than 3500 MHz, and the internal antennas are used for other frequencies (lower than 3500 MHz e.g. As we are at 2.5 km from the emitting antennas with no obstacle between the provider's antennas and our home (there is a small valley in the middle) and at almost the same altitude, the solution of adding an external antenna seemed obvious to try. Furthermore it's impossible to get a 5G link in manual mode (our provider announces 5G NSA service at 700 MHz and 3500 MHz for this station 4G at 700 MHz is well received in manual mode 5G is present in full auto mode of the router but with a worse performance than any 4G mode). But RSRP, RSRQ and SINR are not stable even on short periods of measurement with SINR between -2 and 14 dB. First trials with the integrated antenna resulted in pretty good results in 4G modes at 30 to 110 Mbit/s downloading and 15 to 30 Mbit/s uploading at different hours of the day. We just bought a NR5101 to have a better bandwidth than our poor ADSL line, being at 2.5 km from of a mast of our 4G/5G mobile provider with better speed already than the ADSL line with a simple mobile phone. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |